Company philosophysaving, efficient, harmonious and pragmatic
PRODUCT  service
Product menu
YC-902 series of drum automatic aging machine
    Publish time 2019-07-23 08:50    

一、Introduction to equipment
  YC-902 series of drum automatic aging machine - is our company for the lead-type aluminum electrolytic capacitor developed by a set of automatic boost aging, test sorting as one of the aging test equipment; the device using automatic preset boost Mode to automatically boost the high temperature aging, and to fully mechanized operation design, breaking the traditional aging equipment to be equipped with compressed air to run the limitations of the use of my company's latest research and development of the fifth generation of mechanical feed, to ensure that the machine feeding rate And the stability of the equipment, effectively improve the production efficiency, reduce unnecessary waste and labor costs.
1, the aging temperature: in the room temperature to 105 ℃ within the free set;
2, the device weight about 2500KG;
3, equipment size (area): 3600 (L) × 3000 (W) × 2100 (H) mm;
4, the total power of about 10KW equipment, the normal production of the average operating power ≤ 6KW

二、Adaptation scope

Product Model

product shell number

Aluminum height

Production voltage

The number of racks

Number of clamps

Number of products carried

Thickness of partition

Aging power supply






90 only

14400 only

1.8 mm







75 only

12000 only

2.4 mm

8 segment






60 only

9600  only

2.4 mm

8 segment

1, the capacity test range: 0.01μF ~ 10000μF; test accuracy: ± 1%;
2, the loss angle: 0.001-0.999, the test accuracy: ± 1.0% ± 1 word;
3, the capacity test frequency: 120Hz, 1KHz can be set alone;
4, leakage current test range: 0.005μA-9999μA, test accuracy: ± 1% ± 0.2μA, two leakage test;
5, ESR test range (optional): 0.01mΩ-999kΩ, test accuracy of ± 1.0%, ESR test frequency: 1K / 10K / 20K / 100K Hz can be set alone;

三、working principle
1, the product guide needle shaping and do the polarity detection, open circuit, short circuit detection; exclusion open, bending feet and short circuit products;
2, the product into the oven for high temperature by the linear power supply charging aging;
3, the product after the discharge cooling, the aging product is not detected, will exclude the aging products;
4, the product recharging about 40 seconds after the leakage current test;
5, the product after discharge capacity and loss of the angle test;
6, the product after the discharge by the "ESR" test (optional);
7, the test results are: high impedance, high capacity, low capacity, high loss, leakage large, good products, re-seized goods;
8, the machine using standard instrumentation test, which can effectively improve the accuracy of the parameters;
9, the device uses the latest generation of transport folder, which can effectively guarantee the service life;

四、Equipment performance

Aging time


90 minute/160 One

100 minute/144 One

110 minute/130 One

120 minute/120 One

130 minute/110 One

140 minute/102 One

170 minute/85 One



80 minute/140 One

90 minute/133 One

100 minute/120 One

110 minute/109 One

120 minute/100 One

140 minute/85 One

160 minute/75 One



70 minute/137 One

80 minute/120 One

90 minute/106 One

100 minute/96 One

110 minute/87 One

130 minute/73 One

150 minute/64 One


1, the number of incoming and outgoing materials for the "test run" the actual number of minutes per minute, the error within ± 2;
2, the user can according to their own characteristics of the product stalls to select the product to ensure that the aging effect.
3, leakage test power and charging power and not aging Charging power and test power are used to establish an independent way to effectively ensure the accuracy of product testing.

五、Use environmental conditions

11, using three-phase five-wire AC380V ± 5% 50Hz / 10KVA power supply;
2, the use of ambient temperature: room temperature;
3, the characteristics of the guarantee range: 23 ± 5 ℃, 45 ~ 75% RH;


Contact us
About us
XML 地图 | Sitemap 地图